DIN 8075:2018 – Rohre aus Polyethylen (PE) – PE 80, PE 100 – Allgemeine Güteanforderungen, Prüfungen; Text Deutsch und Englisch
DIN 8075:2018 – Rohre aus Polyethylen (PE) – PE 80, PE 100 – Allgemeine Güteanforderungen, Prüfungen; Text Deutsch und Englisch
1scope
This document applies to straight, round, seamlesspipes made of polyethylene PE 80 and PE 100 withmelt-mass flow rates from nominal 0,20 g/10 minup to 1,4 g/10 min, measured at 190 C/5 kg.
This document is also valid for co-extruded layerpipes with regard to thegeneral qualityrequirements; provided that the layers are made ofmaterials with the same MRS-classification and thelayers are substance-to-substance connected toeach other. Additional requirements for the pipesare laid down in the European product standards.
lt is pointed out that European product standardsfor specific scopes of application are available,which shall be taken into consideration. Some ofthese European product standards are listed in thebibliography for information. The Europeanstandards are subject of a continuous revision,therefore the completeness of the list cannot beguaranteed.
2Normative references
The following documents, in whole or in part, arenormatively referenced in this document and areindispensable for itsapplication. Fordatedreferences,only the edition cited applies. Forundated references,the latest edition of thereferenced document (including any amendments)applies.
DIN 323-1,Preferred Numbers and Series ofPreferred Numbers —Basic Values, Calculatedvalues, Rounded Values
DIN 8074:2011-12,Polyethylene(PE)—PipesPE 80,PE 100 — Dimensions; Text in German andEnglish
DIN CEN/TS 14541 (DIN SPEC 16498), Plasticspipes and fittings -Characteristics for utilisation ofnon-virgin PVC-U,PP and PE materials
DIN EN ISO 1133-1,Plastics – Determination of themelt mass-flow rate (MFR) and the melt volume-flow rate(MVR)of thermoplastics —Part 1:Standard method
DIN EN ISO 1167-1,Thermoplastics pipes,fittingsand assemblies for the conveyance of fiuids —Determination of theresistancetointernalpressure- Part 1: General method
DIN EN ISO 1167-2,Thermoplastics pipes,fittingsand assemblies for the conveyance of fluids—Determination of theresistancetointernalpressure -Part 2:Preparation of pipe test pieces
DIN EN ISO 1183-1,Plastics — Methods fordetermining the density of non-cellular plastics-Part 1:lmmersion method,liquidpyknometermethod and titration method
DIN EN lSO 1183-2, Plastics — Methodsfordetermining the density of non-cellular plastics —Part 2: Density gradient column method
DIN EN ISO 1183-3, Plastics —Methodsfordetermining the density of non-cellular plastics—Part 3: Gas pyknometer method
DIN EN ISO 2505,Thermoplasticspipes —Longitudinalreversion —Test methods andparameters
DIN EN ISO 9080,Plasticspipingandductingsystems —Determinationof thelong-termhydrostatic strength of thermoplastic materials inpipe form by extrapolation
DIN EN ISO 12162,Thermoplastics materials forpipes and fittings for pressureapplications ——classification, designation and design coefficient
DIN EN ISO 11357-6, Plastics —Differentialscanning calorimetry (DSc) —Part 6: Determinationof oxidation induction time (isothermal oIT) andoxidation induction temperature (dynamic orT)
- DIN 7969:2017 – Senkschrauben mit Schlitz mit Sechskantmutter für Stahlkonstruktionen
- DIN 7990:2017 – Sechskantschrauben mit Sechskantmutter für Stahlkonstruktionen
- DIN 9841:2017 – Zylinderschrauben mit Innensechskant und Ansatzschaft für Werkzeuge der Stanztechnik
- DIN 10106:2017 – Mikrobiologische Untersuchung von Fleisch und Fleischerzeugnissen – Bestimmung von Enterococcus faecalis und Enterococcus faecium – Spatelverfahren (Referenzverfahren)
- DIN 10507:2017 – Lebensmittelhygiene – Herstellung und Abgabe von Sahne mit Sahneaufschlagmaschinen – Hygieneanforderungen, Prüfung
- DIN 10528:2017 – Lebensmittelhygiene – Anleitung für die Auswahl von Werkstoffen für den Kontakt mit Lebensmitteln – Allgemeine Grundsätze
- DIN 13093:2017 – Screeningverfahren für die Nickelabgabe aus Erzeugnissen, die in durchstochene Körperteile eingeführt werden, und Erzeugnissen, die unmittelbar und länger mit der Haut in Berührung kommen; Text Deutsch und Englisch
- DIN 15781:2017 – Veranstaltungstechnik – Medienserver
- DIN 16002:2017 – Mechanische Druck- und Temperaturmessgeräte – Druckmessgeräte für Absolutdruck – Maße,Messtechnik, Anforderungen und Prüfung
- DIN 16609:2017 – Drucktechnik – Durchdruck – Begriffe
- DIN 30734:2018 – Einkammer-Wechsel-Silo (Freifall) für Silo-Absetz- und Abrollkipper-Fahrzeuge – Anschlussmaße und Anforderungen
- DIN 6799:2017 – Sicherungsscheiben (Haltescheiben) für Wellen
- DIN 21907:2018 – Bergmännisches Risswerk – Blattgestaltung
- DIN 6444:2020 – Holzbohrer– Schlangenbohrer
- DIN 87373:2018 – Gestängerohr-Fernbedienungen – Durchführungen, wasserdicht
- DIN 10528:2017 – Lebensmittelhygiene – Anleitung für die Auswahl von Werkstoffen für den Kontakt mit Lebensmitteln – Allgemeine Grundsätze
- DIN 7969:2017 – Senkschrauben mit Schlitz mit Sechskantmutter für Stahlkonstruktionen
- DIN EN 2387:2018 – Luft und Raumfahrt – Aluminiumlegierung 2014A – T6 – Konstruktionsrohre – 0,6 mm ≤ a ≤ 12,5 mm; Deutsche und Englische Fassung FprEN 2387:2018
- DIN EN 2279:2018 – Luft- und Raumfahrt -Stahl FE-PM37- 900 MPa≤ Rm≤1 100 MPa – Gesenk- und Freiformschmiedesticke – De≤150 mm; Deutsche und Englische Fassung EN 2279:2018
- DIN EN 2541:2018 – Luft und Raumfahrt – Stahl FEPA18 – Abgeschreckt und kaltgezogen – Drähte für Feder – D ≤ 4,0 mm; Deutsche und Englische Fassung FprEN 2541:2018
- DIN 77006 pdf
- DIN 54608 pdf
- DIN 3193 pdf
- DIN 53236 pdf
- DIN 19902 pdf
- DIN 55982 pdf
- DIN 277 pdf
- DIN 52980 pdf
- DIN 51911 pdf
- DIN 51908 pdf
- DIN 51629 pdf
- DIN 51451 pdf
- DIN 50125 pdf
- DIN 50100 pdf
- DIN 45680 pdf
- DIN 43871 pdf
- DIN 35861 pdf
- DIN 34801 pdf
- DIN 33459 pdf
- DIN 32989 pdf
- DIN 31640 pdf
- DIN 30759 pdf
- DIN 30758 pdf
- DIN 30660 pdf
- DIN 28177 pdf
- DIN 28151 pdf
- DIN 28121 pdf
- DIN 27200 pdf
- DIN 25478 pdf
- DIN 25443 pdf